manualshive.com logo in svg

Avaya P332G-ML, Руководство пользователя

Avaya P332G-ML - высококачественный IP-телефон с широким диапазоном функций. Полное руководство пользователя доступно для бесплатного скачивания на нашем сайте. Ознакомьтесь с функционалом и настройками устройства, скачав руководство с manualshive.com. Найдите ответы на все вопросы в вашем руководстве к Avaya P332G-ML.

Поделиться
Скачать
background image

Chapter 1

Overview

P334T

-ML User’s Guide

11

RIP

P334T-ML supports the widely used RIP routing protocol (both RIPv1 and RIPv2). 
The RIPv1 protocol imposes some limitations on the network design with regard to 
subnetting. When operating RIPv1, you must not configure variable length subnet 
masks (VLMS). Each IP network must have a single mask, implying that all subnets 
in a given IP network are of the same size. Also, when operating RIPv1, you must 
not configure supernets, which are networks with a mask smaller than the natural 
net mask of the address class, such as 192.1.0.0 with mask 255.255.0.0 (smaller than 
the natural class C mask which is 255.255.255.0). For detailed descriptions of RIP 
refer to the standards and published literature.
RIPv2 is a new version of the RIP routing protocol, not yet widely used but with 
some advantages over RIPv1. RIPv2 solves some of the problems associated with 
RIPv1. The most important change in RIPv2 is the addition of a subnet mask field 
which allows RIPv2 to support variable length subnets. RIPv2 also includes an 
authentication mechanism similar to the one used in OSPF.
Configuration of the RIP version, 1 or 2, is per IP interface (default is version 1). 
Configuration should be homogenous on all routers on each subnet, i.e. there 
should not be both RIPv1 and RIPv2 routers on the same subnet. However, different 
IP interfaces of the P334T-ML can be configured with different RIP versions (as long 
as all routers on the subnet are configured to the same version).
RIPv2 and RIPv1 are considered the same protocol with regard to redistribution to/
from OSPF and static route preferences.

OSPF

P334T-ML supports the OSPF routing protocol. P334T-ML can be configured as an 
OSPF Autonomous System Boundary Router (ASBR) by configuration of route 
redistribution. P334T-ML can be installed in the OSPF backbone area (area 0.0.0.0) 
or in any OSPF area that is part of a multiple areas network. However, P334T-ML 
cannot be configured to be an OSPF area border router itself.
The P334T-ML supports the equal-cost multipath (ECMP) feature which allows load 
balancing by splitting traffic between several equivalent paths.
While OSPF can be activated with default values for each interface using a single 
command, many of the OSPF parameters are configurable.
For a detailed description of OSPF, refer to the OSPF standards and published 
literature.

Static Routes

Static routes can be configured to the P334T-ML. They are never timed-out, or lost 
over reboot, and can only be removed by manual configuration. Deletion (by 
configuration) of the IP interface deletes the static routes using this interface as well.
A static route becomes inactive if the interface over which it is defined is disabled. 

Содержание P332G-ML































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для P332G-ML

ORiNG IPS-3082GC-24V Quick Installation Manual preview
IPS-3082GC-24V
Бренд: ORiNG Страницы: 2
Ubiquiti EdgePoint EP-S16 Quick Start Manual preview
EdgePoint EP-S16
Бренд: Ubiquiti Страницы: 22
Dexon DIMAX404 User Manual preview
DIMAX404
Бренд: Dexon Страницы: 31
Campbell HUB-SDM5 Instruction Manual preview
HUB-SDM5
Бренд: Campbell Страницы: 10
Extreme Networks ExtremeSwitching SLX 9540 Hardware Installation Manual preview
ExtremeSwitching SLX 9540
Бренд: Extreme Networks Страницы: 108
TP-Link Tapo S210 User Manual preview
Tapo S210
Бренд: TP-Link Страницы: 28
Quintech RFS 0702 Operation And Adjustment Procedure preview
RFS 0702
Бренд: Quintech Страницы: 2
N-Tron 302MC-XX Installation Manual preview
302MC-XX
Бренд: N-Tron Страницы: 16
OTS IES8242MPp9H-S-DR Quick Installation Manual preview
IES8242MPp9H-S-DR
Бренд: OTS Страницы: 3
S&C Omni-Rupter Series Installation And Operation Manual preview
Omni-Rupter Series
Бренд: S&C Страницы: 31
Lantech IES-5222T Series User Manual preview
IES-5222T Series
Бренд: Lantech Страницы: 30
Hammond Leslie CU-1 Owner'S Manual preview
Leslie CU-1
Бренд: Hammond Страницы: 2
AVProEdge AC-MX44/88-AUHD-HDBT User Manual preview
AC-MX44/88-AUHD-HDBT
Бренд: AVProEdge Страницы: 32
Emcotec iRC Electronic DPSI TWIN Mini Quick Reference Manual preview
iRC Electronic DPSI TWIN Mini
Бренд: Emcotec Страницы: 2
Key Digital Champion KD-4X4XC Setup Manual preview
Champion KD-4X4XC
Бренд: Key Digital Страницы: 8
ZIEHL-ABEGG S-ET Series Operating Instructions Manual preview
S-ET Series
Бренд: ZIEHL-ABEGG Страницы: 12
Cooper Crouse-Hinds GHG 264 Operating Instructions Manual preview
GHG 264
Бренд: Cooper Crouse-Hinds Страницы: 24
H3C S9825 Series Manual preview
S9825 Series
Бренд: H3C Страницы: 34

Бренды по названию

Популярные бренды

Загрузить еще бренды