Avaya P332G-ML Скачать руководство пользователя страница 93

Страница: 93 / 254

Chapter 6

CLI – Layer 2

Avaya P334T-ML User’s Guidee

show port autonegotiation-flowcontrol-advertisement

Use the s

how port autonegotiation-flowcontrol-advertisement

command to display the flowcontrol advertisement for a Gigabit port used to
perform autonegotiation.

Note:

This command is applicable to 1000Mbps ports only.

The syntax for this command is:

show port autonegotiation-flowcontrol-advertisement

[<mod_num>[/<port_num>]]

Output Example:

P330-N> show port autonegotiation-flowcontrol-advertisement

Port 1/1 advertises no flow control capabilities.

Port 1/2 advertises no flow control capabilities.

Port 1/3 advertises no flow control capabilities.

etc.

show trunk

Use the

show trunk

command to display VLAN tagging information of the

ports, port binding mode, and the port VLAN ID.

The syntax for this command is:

show trunk

[<mod_num>[/<port_num>]]

Output Example:

P330-N> show trunk

Port Mode Binding mode Native vlan

------ ----- ----------------------------- -----------

1/1 dot1q bound to configured vlans 1

1/2 dot1q bound to all vlans 1

1/3 off statically bound 1

1/4 off statically bound 1

1/5 off statically bound 1

mod_num

Number of the switch

port num

Number of the port

Содержание P332G-ML































































































































































































































































Результаты поиска

Содержание P332G-ML

Отзывы:

Похожие инструкции для P332G-ML

Бренды по названию

Популярные бренды

Avaya P332G-ML, Руководство пользователя

Результаты поиска

Содержание P332G-ML

Отзывы:

Похожие инструкции для P332G-ML

Бренды по названию

Популярные бренды