Avaya P332G-ML Скачать руководство пользователя страница 187

Страница: 187 / 254

Chapter 7

CLI – Layer 3

P334T-ML User’s Guide

169

ip routing Command

Use the

ip routing

command to enable IP routing. The

form of this

command disables the IP routing process in the device. By default, IP routing is
enabled.

The syntax for this command is:

[no] ip routing

ip max-route-entries Command

This command exists for compatibility with P550. There is no limitation on the size
of the routing table, except for the amount of available memory.

The syntax for this command is:

[no] ip max-route-entries <value>

arp Command

Use the

arp

command to add a permanent entry to the Address Resolution

Protocol (ARP) cache. The

form of this command removes an entry, either a

static entry or a dynamically learned entry.

The syntax for this command is:

[no] arp

<ip-address> <mac-address>

Example:
To add a permanent entry for station 192.168.7.8 to the ARP cache:

Router(configure)#

arp 192.168.7.8 00:40:0d:8c:2a:01

To remove an entry to the ARP cache for the station 192.168.13.76:

Router(configure)#

no arp 192.168.13.76

value

number of entries

ip-address

IP address, in dotted decimal format, of the station

mac-address

MAC address of the local data link

Содержание P332G-ML































































































































































































































































Результаты поиска

Содержание P332G-ML

Отзывы:

Похожие инструкции для P332G-ML

Бренды по названию

Популярные бренды

Avaya P332G-ML, Руководство пользователя

Результаты поиска

Содержание P332G-ML

Отзывы:

Похожие инструкции для P332G-ML

Бренды по названию

Популярные бренды