Avaya P332G-ML Скачать руководство пользователя страница 143

Страница: 143 / 254

Chapter 6

CLI – Layer 2

Avaya P334T-ML User’s Guidee

125

set port autonegotiation-flowcontrol-advertisement

The

set port autonegotiation-flowcontrol-advertisement

command

sets the flowcontrol advertisement for a Gigabit port when performing
autonegotiation.

Note:

Using the

set port autonegotiation-flowcontrol-advertisement

not supported on 10/100BaseT ports .

The syntax for this command is:

set port autonegotiation-flowcontrol-advertisement

<mod_num>/

<port_num> {no-flowcontrol|asym-tx-only|sym-only|sym-and-asym-rx}

Output Example:

P330-N# set port autonegotiation-flowcontrol-advertisement 1/

5 asym-tx-only

P330-N# Port 1/5 pause capabilities was set

set trunk

Use the

set trunk

command to configure the tagging mode of a post.

set trunk

[module/port] [value]

Output Example:

P330-1(super)# set trunk 2/20 dot1q

Dot1Q VLAN tagging set on port 2/20.

no-flowcontrol

The port will advertise no pause capabilities.

asym-tx-only

The port will advertise asymmetric Tx pause capabilities only.

sym-only

The port will advertise symmetric pause capabilities only.

sym-and-asym-rx

The port will advertise both symmetric and asymmetric Rx
pause capabilities.

module/port

module/port number

value

off/dot1q

Содержание P332G-ML































































































































































































































































Результаты поиска

Содержание P332G-ML

Отзывы:

Похожие инструкции для P332G-ML

Бренды по названию

Популярные бренды

Avaya P332G-ML, Руководство пользователя

Результаты поиска

Содержание P332G-ML

Отзывы:

Похожие инструкции для P332G-ML

Бренды по названию

Популярные бренды