Avaya P332G-ML Скачать руководство пользователя страница 216

Страница: 216 / 254

Chapter 7

CLI – Layer 3

198

P334T-ML User’s Guide

Configure Mode

router srrp Command

Use the

router srrp

command to configure SRRP options, activate SRRP and

enter the SRRP configuration mode. The

form of this command disables it

globally. The default is

disabled

Note:

You cannot activate both VRRP and SRRP protocols at the same time.

The syntax for this command is:

[no] router srrp

Router-SRRP Mode

poll-interval Command

Use the

poll-interval

command to configure the polling interval in seconds

used by SRRP. Use the

form of this command to return to the default polling

interval of 1 second.

The syntax for this command is:

[no] poll-interval

Example:

Router-N(configure router:srrp)# poll-interval 4

timeout Command

Use the

timeout

command to configure the timeout (in seconds) after which

SRRP declares the main router dead if it does not reply to polling.
Use the

form of this command to return to default timeout interval of 12

seconds.

The syntax for this command is:

[no] timeout <timeout>

poll interval

An integer (in seconds)

timeout

An integer (in seconds)

Содержание P332G-ML































































































































































































































































Результаты поиска

Содержание P332G-ML

Отзывы:

Похожие инструкции для P332G-ML

Бренды по названию

Популярные бренды

Avaya P332G-ML, Руководство пользователя

Результаты поиска

Содержание P332G-ML

Отзывы:

Похожие инструкции для P332G-ML

Бренды по названию

Популярные бренды