Avaya P332G-ML Скачать руководство пользователя страница 112

Страница: 112 / 254

Chapter 6

CLI – Layer 2

Avaya P334T-ML User’s Guide

no rmon event

Use the

no rmon event

command to delete an existing RMON event entry.

The syntax for this command is:

no rmon event

hostname

Use the

hostname

command to change the Command Line Interface (CLI)

prompt. The current switch number always appears at the end of the prompt.

The syntax for this command is:

hostname

[<hostname_string>]

Note:

If this command is to be implemented on a switch other than the stack master,

a session should be opened to the relevant switch.

Clear Commands Summary Table

Following is a Table of the Privileged Level

clear

commands.

hostname_string

none

– displays current hostname

string

– the string to be used as the hostname

(up to 20 characters).

• clear timezone

Returns the timezone to its default, UTC.

Page 95

• clear ip route

Clears IP routing table entries.

Page 95

• clear snmp trap

Clears SNMP trap on the system.

Page 95

• clear vlan

Clears VLAN entries.

Page 96

• clear dynamic vlans

Clears dynamic VLAN entries.

Page 96

• clear port static-vlan

Clears a VLAN statically configured on a
port.

Page 97

• clear cam

Clears all the CAM entries.

Page 97

• clear log

Clears the Log entries of a switch.

Page 97

• clear port mirror

Cancels port mirroring.

Page 97

Содержание P332G-ML































































































































































































































































Результаты поиска

Содержание P332G-ML

Отзывы:

Похожие инструкции для P332G-ML

Бренды по названию

Популярные бренды

Avaya P332G-ML, Руководство пользователя

Результаты поиска

Содержание P332G-ML

Отзывы:

Похожие инструкции для P332G-ML

Бренды по названию

Популярные бренды