Avaya P332G-ML Скачать руководство пользователя страница 118

Страница: 118 / 254

Chapter 6

CLI – Layer 2

100

Avaya P334T-ML User’s Guide

• set port disable

Administratively disables a port.

Page 111

• set port speed

Sets the speed for a 10/100 port.

Page 112

• set port duplex

Sets the duplex mode of a port.

Page 112

• set port name

Assigns a name to a port.

Page 114

• set port trap

Enables/disables the SNMP up/down
link traps sent for port.

Page 114

• set port vlan

Assigns the Port VLAN ID (PVID).

Page 114

• set port vlan-binding-

mode

Defines the port binding method.

Page 115

• set port static-vlan

Defines a multiple VLANs per port.

Page 115

• set port channel

Defines a LAG interface.

Page 116

• set port classification

Defines port classification.

Page 116

• set port redundancy

on/off

Defines/deletes a link redundancy
entry.

Page 117

• set port redundancy

Enables/disables all the defined link
redundancy schemes.

Page 117

• set internal buffering

Sets internal buffering capacity to
maximum/minimum.

Page 118

• set boot bank

Configures the boot bank from which
the switch will boot.

Page 118

• set intermodule port

redundancy

Defines the stack’s unique fast
redundancy scheme.

Page 119

• set intermodule port

redundancy off

Clears the intermodule redundancy.

Page 120

• set port mirror

Sets a port mirroring source-destination
pair in the stack.

Page 120

• set port spantree

Enables or disables the spanning tree for
switch ports.

Page 120

• set port spantree

priority

Sets the port spantree priority level.

Page 121

• set port spantree cost

Sets the port spantree cost.

Page 121

Содержание P332G-ML































































































































































































































































Результаты поиска

Содержание P332G-ML

Отзывы:

Похожие инструкции для P332G-ML

Бренды по названию

Популярные бренды

Avaya P332G-ML, Руководство пользователя

Результаты поиска

Содержание P332G-ML

Отзывы:

Похожие инструкции для P332G-ML

Бренды по названию

Популярные бренды