Avaya P332G-ML Скачать руководство пользователя страница 142

Страница: 142 / 254

Chapter 6

CLI – Layer 2

124

Avaya P334T-ML User’s Guide

Output Example:

P330-1(super)# set port flowcontrol all 2/20 on

Port 2/20 flow control administration status set to on

Field

Description

receive

Controls the receipt of IEEE802.3x flow-control frames on Gigabit
ports only:
• ON indicates that the local port will act upon flow control

frames received from the far end.

• OFF indicates that the local port will discard flow control

frames received from the far end.

send

Controls the sending of IEEE802.3x flow-control frames from
Gigabit ports only:
• ON indicates that the local port is allowed to send flow control

frames to the far end.

• OFF indicates that the local port is

not

allowed to send flow

control frames to the far end.

all

Controls the sending and receipt of flow-control frames for any
type of ports:
• ON indicates that the local port will both act upon and send

IEEE802.3x flow control frames.

• OFF indicates that the local port will both discard and not send

flow control frames (of any type).

• PROPRIETARY indicates that the local port will both act upon

and send Avaya proprietary flow control frames.

proprietary

A proprietary flow control which may be used when a P330 is
connected to M770 10/100 ports or P110 ports.

module/
port

Switch number/port number

Содержание P332G-ML































































































































































































































































Результаты поиска

Содержание P332G-ML

Отзывы:

Похожие инструкции для P332G-ML

Бренды по названию

Популярные бренды

Avaya P332G-ML, Руководство пользователя

Результаты поиска

Содержание P332G-ML

Отзывы:

Похожие инструкции для P332G-ML

Бренды по названию

Популярные бренды