Avaya P332G-ML Скачать руководство пользователя страница 141

Страница: 141 / 254

Chapter 6

CLI – Layer 2

Avaya P334T-ML User’s Guidee

123

The syntax for this command is:

set inband vlan

<value>

Output Example:

P330-N# set inband vlan 1

Management VLAN number set to 1

set vlan

Use the

set vlan

command to create VLANs.

The syntax for this command is:

set vlan

<vlan-id> [name <vlan-name>]

Output Example:

P330-N# set vlan 3 name v3

VLAN ID 3 is named v3.

Note:

If you wish to define a name which includes spaces, you must enclose the

entire name in quotation marks, e.g. "new york".

set port flowcontrol

Use the

set port flowcontrol

command to set the send/receive mode for

flow-control frames (IEEE 802.3x or proprietary) for a full duplex port. Each
direction (send or receive) can be configured separately only for Gigabit Ethernet
ports. Proprietary flow control cannot be configured on Gigabit ports. The

set

flowcontrol

command cannot be used on Gigabit ports for which

autonegotiation is enabled.

The syntax for this command is:

set flowcontrol

[direction] [module/port] [value]

where the parameters of

direction

are

receive|send|all

, and the parameters

value

are

on|off|proprietary

value

A VLAN number between 1 and 3071.

vlan-id

vlan number

vlan-name

vlan name

Содержание P332G-ML































































































































































































































































Результаты поиска

Содержание P332G-ML

Отзывы:

Похожие инструкции для P332G-ML

Бренды по названию

Популярные бренды

Avaya P332G-ML, Руководство пользователя

Результаты поиска

Содержание P332G-ML

Отзывы:

Похожие инструкции для P332G-ML

Бренды по названию

Популярные бренды