Avaya P332G-ML Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 254

background image

Chapter 1

Overview

P334T

-ML User’s Guide

17

Avaya P334T-ML Network Monitoring

RMON I MIBs - RFC 1757

•

RMON I support for the following standard monitoring MIBs:
— Statistics
— History
— Alarms
— Events

SMON MIBs - RFC 2613

•

SMON support for the following standard monitoring MIBs:
— Data Source Capabilities
— Port Copy
— VLAN and Priority Statistics.

Bridge MIB Groups - RFC 2674

•

dot1dbase and dot1dStp fully implemented.

•

Support for relevant MIB objects: dot1q (dot1qBase, dot1qVlanCurrent).

Port Mirroring

The P334T-ML provides port mirroring for additional network monitoring
functionality. You can filter the traffic and mirror either incoming traffic to the
source port or both incoming and outgoing traffic. This allows you to monitor the
network traffic you need.
Ports which are members in a Link Aggregation Group (LAG) cannot

also

be used as

Port Mirroring Destination or Source ports.
Within the P334T-ML switch, port mirroring can be configured between ports in the
three following groups:
•

1-12, 25-36

•

13-24, 37-48

•

51, 52

On the stack level, port mirroring pairs can be configured between any Giga port,
and between any Giga port on the P334T-ML and any 10/100Mbps port not residing
on a P334T-ML.

SMON

The P334T-ML supports Avaya’s ground-breaking SMON Switched Network
Monitoring, which the IETF has now adopted as a standard (RFC2613). SMON
provides unprecedented top-down monitoring of switched network traffic at the

«
...
33
34
35
36
37
...
»

Содержание P332G-ML































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для P332G-ML

Бренд: Black Box Страницы: 28

Бренд: Cabletron Systems Страницы: 83

Бренд: Conceptronic Страницы: 7

Бренд: Quartz Страницы: 43

Бренд: M-system Страницы: 4

Бренд: HDTV Supply Страницы: 21

Бренд: I-Tech Страницы: 19

Бренд: Linkskey Страницы: 2

Бренд: Byte Delight Страницы: 12

ePowerSwitch 8XM Master

Бренд: ADDER Страницы: 2

Бренд: H3C Страницы: 4

Бренд: StarTech.com Страницы: 2

Бренд: LevelOne Страницы: 4

Бренд: Advantech Страницы: 73

Бренд: autenco Страницы: 2

Бренд: Barco Страницы: 2

Бренд: Leviton Страницы: 3

Бренд: ORiNG Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды