APRILIA SPORTCITY ONE 125 Скачать руководство пользователя

Страница: 92 / 176

- Calculate the difference between the two meas-

urements.

- By means of the table, see the SPECIFICA-

TIONS chapter, identify the cylinder base gasket

thickness to be used upon refitting. Correctly iden-

tify the cylinder base gasket thickness to keep the

correct compression ratio.

- Remove the special tool and the cylinder.

Specific tooling

020428Y

Support to check piston position

Refitting the piston rings

- Place the oil scraper spring on the piston.

- Refit the oil scraper ring with the join of spring

ends on the opposite side from the ring gap and

the word 'TOP' towards the crown of the piston.

The tapered side of the middle piston ring should

always be facing away from the crown of the pis-

ton.

- Fit the middle piston ring with the identification

letter facing the crown of the piston. In any case,

the step must be facing opposite the piston top.

- Fit the top piston ring with the word 'top' or the

reference mark facing the crown of the piston.

- Offset the piston ring gaps on the three rings by

120° to each other as shown in the figure.

- Lubricate the components with engine oil.

NOTE

SO AS TO OBTAIN THE BEST CONFIGURATION THE 2
SEALING RINGS ARE MADE WITH A CONTACT CONICAL
CYLINDER SECTION.

Engine

SPORTCITY ONE 125

ENG - 92

Содержание SPORTCITY ONE 125

















































































































































































Результаты поиска

Содержание SPORTCITY ONE 125

Отзывы:

Похожие инструкции для SPORTCITY ONE 125

Бренды по названию

Популярные бренды

APRILIA SPORTCITY ONE 125, Руководство по обслуживанию станции

Результаты поиска

Содержание SPORTCITY ONE 125

Отзывы:

Похожие инструкции для SPORTCITY ONE 125

Бренды по названию

Популярные бренды