APRILIA SPORTCITY ONE 125 Скачать руководство пользователя

Страница: 115 / 176

- Remove the central screw with Belleville washer,

as shown in the diagram.

- Remove the chain with the pulley.

- Remove the crankshaft control pinion.

- Remove the oil pump acting on the 2 retainers as

shown in the figure.

- Remove the oil pump seal.

IT IS ADVISABLE TO MARK THE CHAIN IN ORDER TO EN-
SURE THAT THE INITIAL DIRECTION OF ROTATION IS
MAINTAINED.

Inspection

- Remove the two screws and the oil pump cover.

- Remove the clip retaining the innermost rotor.

- Remove and wash the rotors thoroughly with pet-

rol and compressed air.

- Reassemble the rotors in the pump body, keep-

ing the two reference marks visible Replace the

clip.

- Using a thickness gauge, check the distance be-

tween the rotors in the position shown in the figure.

Characteristic

Maximum clearance admitted

0.12 mm

SPORTCITY ONE 125

Engine

ENG - 115

Содержание SPORTCITY ONE 125

















































































































































































Результаты поиска

Содержание SPORTCITY ONE 125

Отзывы:

Похожие инструкции для SPORTCITY ONE 125

Бренды по названию

Популярные бренды

APRILIA SPORTCITY ONE 125, Руководство по обслуживанию станции

Результаты поиска

Содержание SPORTCITY ONE 125

Отзывы:

Похожие инструкции для SPORTCITY ONE 125

Бренды по названию

Популярные бренды