manualshive.com logo in svg

APRILIA SPORTCITY ONE 125, Руководство по обслуживанию станции

Поделиться
Скачать
APRILIA SPORTCITY ONE 125 Скачать руководство пользователя страница 136

Front wheel hub overhaul

WHEEL BEARINGS

•

Remove the front wheel.

•

Keep the wheel level by means of two

wooden wedges.

•

With the appropriate pliers and tool re-

move the wheel bearing on the side the

odometer detects movement.

•

Slide off the internal spacer.

•

Use appropriate handle, adaptor and

guide to extract the bearing and the

spacer bushing on the brake disc side;

insert handle on the side the odometer

detects movement.

•

Check that the bearings do not show

flaws or jamming. Otherwise, replace

them.

•

Check that the internal spacer does not

show abnormal wear. Otherwise, re-

place it.

•

With a hot air gun heat the seat of the

bearing on the brake calliper side.

•

With an appropriate tool refit the bear-

ing on the brake disc side.

•

Insert the spacer bushing on the brake

disc side.

•

With a hot air gun heat the seat of the bearing on the side the odometer detects movement.

•

Insert the internal spacer with the centring ring facing the brake disc side.

•

Use an appropriate tool to insert the bearing on the odometer movement detector side.

Specific tooling

Suspensions

SPORTCITY ONE 125

SUSP - 136

Содержание SPORTCITY ONE 125

















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды