APRILIA SPORTCITY ONE 125 Скачать руководство пользователя

Страница: 126 / 176

- Introduce the float with the rod on the fuel feeding tube side.

NOTE

INTRODUCE THE RETURN SPRING ON THE FLOAT PLATE ADEQUATELY

- Remove the drainage screw from the tank, wash

and blow it properly and make sure the accelera-

tion pump pipes are clean.

- Operate the acceleration pump piston repeatedly

and blow with compressed air.

- Reassemble the acceleration pump valves fol-

lowing this order:

INTAKE VALVE (A)

•

Spring

•

Ball

•

Nozzle

IN VALVE (M)

•

Ball

•

Spring

•

Nozzle

NOTE

THE IN VALVE NOZZLE, CORRESPONDING TO THE AC-
CELERATION PUMP, IS MILLED.

-Check the screw tightness introducing a small

amount of fuel in the tank.

- Assemble a new gasket on the tank.

- Assemble the tank on the carburettor body fas-

tening the 4 screws.

- Check that the control roller is free to rotate in its

own seat.

NOTE

MAKE SURE THE TANK GASKET IS CORRECTLY INTRO-
DUCED

NOTE

AVOID DEFORMING THE ACCELERATION PUMP CON-
TROL ROCKING LEVER.

- Wash and blow the flow screw properly.

- Check that screw is not deformed and/or rusty.

- Assemble the spring on the screw.

- Screw the flow screw on the carburettor body.

Engine

SPORTCITY ONE 125

ENG - 126

Содержание SPORTCITY ONE 125

















































































































































































Результаты поиска

Содержание SPORTCITY ONE 125

Отзывы:

Похожие инструкции для SPORTCITY ONE 125

Бренды по названию

Популярные бренды

APRILIA SPORTCITY ONE 125, Руководство по обслуживанию станции

Результаты поиска

Содержание SPORTCITY ONE 125

Отзывы:

Похожие инструкции для SPORTCITY ONE 125

Бренды по названию

Популярные бренды