APRILIA SPORTCITY ONE 125 Скачать руководство пользователя

Страница: 80 / 176

- Refit the Seeger ring with the opening facing the

bearing as shown in the figure and fit a new oil

guard flush with the crankcase.

Refitting the wheel axle bearing

- Heat up the parts using the specific heat gun

Specific tooling

020151Y

Air heater

020150Y

Air heater support

-The wheel axle bearing on the cover, should be assembled with the specific tools

Specific tooling

020364Y

25-mm guide

020360Y

Adaptor 52 x 55 mm

020376Y

Adaptor handle

•

Assemble the Seeger ring.

•

Assemble the oil seal flush with the in-

ternal surface as shown in the figure to

the hub using the adequate tools and

with the seal lip towards the inside of

the hub.

Specific tooling

020376Y

Adaptor handle

020360Y

Adaptor 52 x 55 mm

Refitting the hub cover bearings

- For the fitting of the hub box bearings the engine crankcase and the cover must be heated with the

specific heat gun.

Specific tooling

020150Y

Air heater support

020151Y

Air heater

Engine

SPORTCITY ONE 125

ENG - 80

Содержание SPORTCITY ONE 125

















































































































































































Результаты поиска

Содержание SPORTCITY ONE 125

Отзывы:

Похожие инструкции для SPORTCITY ONE 125

Бренды по названию

Популярные бренды

APRILIA SPORTCITY ONE 125, Руководство по обслуживанию станции

Результаты поиска

Содержание SPORTCITY ONE 125

Отзывы:

Похожие инструкции для SPORTCITY ONE 125

Бренды по названию

Популярные бренды