manualshive.com logo in svg

APRILIA SPORTCITY ONE 125, Руководство по обслуживанию станции

Поделиться
Скачать
APRILIA SPORTCITY ONE 125 Скачать руководство пользователя страница 50

Coil primary check:

•

Disconnect the connector of the control

unit.

•

Measure the resistance present be-

tween terminals No. 4 (White-Purple

cable) and No. 12 (Blue cable).

•

If the measured value is incorrect, re-

peat the check between the positive

and negative terminals of the coil.

•

If a correct value is measured, check

wiring continuity.

Characteristic

Coil primary resistance value:

~ 0.5 

Ω

Coil secondary check

•

Disconnect the spark plug cap from the

coil cable and measure the resistance

between the cable end and the coil

negative terminal.

Characteristic

Coil secondary resistance value:

3000 ± 300 

Ω

Battery recharge circuit

With engine running at high revs, measure the voltage present at the battery poles.

Characteristic

Battery recharging voltage:

13 ÷ 14.5 V at 4000 rpm

Electrical system

SPORTCITY ONE 125

ELE SYS - 50

Содержание SPORTCITY ONE 125

















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды