APRILIA SPORTCITY ONE 125 Скачать руководство пользователя страница 155

Страница: 155 / 176

Front brake pump

Removal

•

Remove the front and rear handlebar covers.

•

Remove the brake pipes and the contacts of the stop light switch.

•

Undo the two screws «1».

To refit, carry out the removal operations but in reverse order and tighten the screws to the prescribed

torque.

ONCE REFITTING IS FINISHED, BLEED THE SYSTEM.

Locking torques (N*m)

Brake pump to handlebar fixing screw

8.05

Brake pipe to brake pump fixing screw

Rear drum brake

•

Remove the rear wheel.

•

Hold the lower shoe and slide it with the

upper one.

For fitting:

•

First assembly two shoes and the

springs then place them on the pin and

on the cam.

To replace the transmission:

•

Remove the front handlebar cover.

•

Loosen the brake set screw

•

Release the transmission from its

clamps to the engine and from its

clamps to the chassis.

•

Adjust the drum brake activation point.

Locking torques (N*m)

SPORTCITY ONE 125

Braking system

BRAK SYS - 155

Содержание SPORTCITY ONE 125

















































































































































































Результаты поиска

Содержание SPORTCITY ONE 125

Отзывы:

Бренды по названию

Популярные бренды

APRILIA SPORTCITY ONE 125, Руководство по обслуживанию станции

Результаты поиска

Содержание SPORTCITY ONE 125

Отзывы:

Бренды по названию

Популярные бренды