APRILIA SPORTCITY ONE 125 Скачать руководство пользователя страница 76

Страница: 76 / 176

- Open the rear pulley and insert the belt observing

the correct direction of rotation.

WARNING

IT IS MOST IMPORTANT THAT WHEN FITTING THE FRONT
PULLEY UNIT, THE BELT IS FREE INSIDE SO AS TO AVOID
A WRONG TIGHTENING OF THE DRIVING HALF-PULLEY.

Refitting the driving pulley

- Reassemble the parts of the unit (internal lining,

fixed half-pulley, external lining, drive and nut),

spread threadlock on the thread and screw the nut

to the prescribed torque.

-Avoid the half-pulley rotation using a calliper

spanner

NOTE

REPLACE THE NUT WITH A NEW ONE AT EVERY REFIT

Specific tooling

020368Y

driving pulley lock wrench

Recommended products

Loctite 243

Medium-strength threadlock

Loctite 243 medium-strength threadlock

Locking torques (N*m)

Locking torque

75 ÷ 83

Refitting the transmission cover

- Check the presence of the 2 centring dowels and the correct installation of the sealing gasket for the

oil sump on the transmission cover.

- Replace the cover tightening the 10 screws at the specified torque.

- Refit the oil loading cap/bar.

- refit the steel washer and the driven pulley nut.

- Tighten the nut to the prescribed torque using the lock wrench and the torque wrench tools.

- Replace the plastic cover.

Specific tooling

020423Y

Driven pulley lock wrench

Locking torques (N*m)

Transmission cover screws

11 ÷ 13

Driven pulley shaft nut

54 ÷ 60

Engine

SPORTCITY ONE 125

ENG - 76

Содержание SPORTCITY ONE 125

















































































































































































Результаты поиска

Содержание SPORTCITY ONE 125

Отзывы:

Бренды по названию

Популярные бренды

APRILIA SPORTCITY ONE 125, Руководство по обслуживанию станции

Результаты поиска

Содержание SPORTCITY ONE 125

Отзывы:

Бренды по названию

Популярные бренды