APRILIA SPORTCITY ONE 125 Скачать руководство пользователя страница 98

Страница: 98 / 176

Minimum admitted diameter bearing A

Ø: 32.440 mm

Minimum admitted diameter bearing B

Ø: 19.950 mm

Inlet cam height

27.512 mm

Outlet cam height

27.212 mm

- Check there is no wear on the cam shaft retaining

plate and its associated groove on the cam shaft.

- If any of the above dimensions are outside the

specified limits, or there are signs of excessive

wear, replace the defective components with new

ones.

Characteristic

Maximum axial clearance admitted

0.42 mm

- Check there are no signs of wear on the auto-

matic valve-lifter cam, or the end-of stroke roller,

or the rubber buffer on the automatic valve-lifter

retaining cover.

- Check that the valve lifting spring has not yielded.

- Replace any defective or worn components.

- Check there are no signs of scoring or wear on

the rocking lever bolt.

Check there are no signs of wear on the pad from

contact with the cam and on the jointed adjustment

plate.

- Measure the internal diameter of each rocking

lever.

-Check that the elastic washer dedicated to the

axle clearance of the rocking levers is not worn. -

Engine

SPORTCITY ONE 125

ENG - 98

Содержание SPORTCITY ONE 125

















































































































































































Результаты поиска

Содержание SPORTCITY ONE 125

Отзывы:

Бренды по названию

Популярные бренды

APRILIA SPORTCITY ONE 125, Руководство по обслуживанию станции

Результаты поиска

Содержание SPORTCITY ONE 125

Отзывы:

Бренды по названию

Популярные бренды