APRILIA SPORTCITY ONE 125 Скачать руководство пользователя страница 94

Страница: 94 / 176

Inspecting the timing system components

- Check that the guide shoe and the tensioner shoe

are not worn out.

- Ensure that the camshaft drive pulley, the chain

assembly and the sprocket wheel are not worn.

- If sings of wear are found, replace the parts. if the

chain, pinion or pulley are worn, replace the whole

assembly.

- Remove the central screw and the tensioner

spring. Check that the one-way mechanism is not

worn.

- Check the condition of the tensioner spring.

- If examples of wear are found, replace the whole

assembly.

Inspecting the valve sealings

- Measure the width of the sealing surface on the valve seats.

VALVE SEAL SURFACE

Specification

Desc./Quantity

Inlet valve - seal surface

2.4 ÷ 2.8 mm

Outlet valve - seal surface

2.2 ÷ 2.6 mm

Inspecting the valve housings

- Remove any carbon formation from the valve guides.

- Measure the inside diameter of each valve guide.

- Take the measurement at three different heights in the rocker arm push direction.

Engine

SPORTCITY ONE 125

ENG - 94

Содержание SPORTCITY ONE 125

















































































































































































Результаты поиска

Содержание SPORTCITY ONE 125

Отзывы:

Бренды по названию

Популярные бренды

APRILIA SPORTCITY ONE 125, Руководство по обслуживанию станции

Результаты поиска

Содержание SPORTCITY ONE 125

Отзывы:

Бренды по названию

Популярные бренды