APRILIA SPORTCITY ONE 125 Скачать руководство пользователя

Страница: 33 / 176

•

Screw and tighten the cap-dipstick «1».

•

Start the engine and let it run for several minutes. Stop the engine and let it cool down.

•

Check the engine oil level.

Check

NOTE

USE RECOMMENDED OIL ONLY. REFER TO THE RECOMMENDED PRODUCTS TABLE.

NOTE

PARK THE VEHICLE ON SAFE AND LEVEL GROUND.

•

Rest the vehicle on its centre stand.

CAUTION

WAIT SOME MINUTES UNTIL THE ENGINE AND THE EXHAUST SYSTEM ARE COLD.

•

Stop the engine and let it cool off so

that the oil in the crankcase flows down

and cools as well.

NOTE

FAILURE TO FOLLOW THESE OPERATIONS MAY RE-
SULT IN AN INCORRECT READING OF THE ENGINE OIL
LEVEL.

•

Unscrew and pull out the measuring

cap-dipstick «1».

•

Clean the area in contact with oil with

a clean cloth.

•

Screw the cap-dipstick «1» fully into its

tube.

•

Remove the tap-dipstick «1» again and

read the level the oil reaches on the

dipstick:

MAX

= maximum level;

MIN

= minimum level.

•

The level is correct when it is close to

the «MAX» level marked on the meas-

uring dipstick.

CAUTION

SPORTCITY ONE 125

Maintenance

MAIN - 33

Содержание SPORTCITY ONE 125

















































































































































































Результаты поиска

Содержание SPORTCITY ONE 125

Отзывы:

Похожие инструкции для SPORTCITY ONE 125

Бренды по названию

Популярные бренды

APRILIA SPORTCITY ONE 125, Руководство по обслуживанию станции

Результаты поиска

Содержание SPORTCITY ONE 125

Отзывы:

Похожие инструкции для SPORTCITY ONE 125

Бренды по названию

Популярные бренды