APRILIA SPORTCITY ONE 125 Скачать руководство пользователя

Страница: 108 / 176

TO KEEP THIS POSITION OF THE BUSHINGS ON THE
CRANKCASE, FITTING IS FORCED ON STEEL RINGS IN-
SERTED IN THE CASTING OF BOTH CRANKCASE
HALVES.

Characteristic

Standard driving depth

1.35 ÷ 1.6

- Check the inside diameter of the main bushings in the three directions indicated in the diagram.

- Repeat the measurements for the other bushing half. see diagram.

- The standard bushing diameter after driving is variable on the basis of a coupling selection.

- The bushing housings in the crankcase are classified into 2 categories - Cat. 1 and Cat. 2 - just like

those for the crankshaft.

3 - The main bushings are subdivided into 3 thickness categories; see the table below:

NOTE

DO NOT TAKE THE MEASUREMENT ON THE TWO HALF-SHELL COUPLING SURFACE SINCE
THE ENDS ARE RELIEVED TO ALLOW BENDING DURING THE DRIVING OPERATION.

MAIN BEARINGS

Specification

Desc./Quantity

Blue

Yellow

Green

Refitting the crankcase halves

- Fit the internal bulkhead by locking the two

screws to the prescribed torque.

Locking torques (N*m)

Locking torque

4 ÷ 6

Engine

SPORTCITY ONE 125

ENG - 108

Содержание SPORTCITY ONE 125

















































































































































































Результаты поиска

Содержание SPORTCITY ONE 125

Отзывы:

Похожие инструкции для SPORTCITY ONE 125

Бренды по названию

Популярные бренды

APRILIA SPORTCITY ONE 125, Руководство по обслуживанию станции

Результаты поиска

Содержание SPORTCITY ONE 125

Отзывы:

Похожие инструкции для SPORTCITY ONE 125

Бренды по названию

Популярные бренды