APRILIA SPORTCITY ONE 125 Скачать руководство пользователя страница 78

Страница: 78 / 176

Removing the hub bearings

- Check the state of the bearings being examined

(wear, clearance and noisiness). If faults are de-

tected, do the following.

- Use the specific bearing extractor to remove the

three 15 mm bearings (2 in the crankcase and 1 in

the hub cover).

Specific tooling

001467Y009

Bell for OD 42-mm bearings

001467Y013

Calliper to extract 15-mm diame-

ter bearings

Removing the wheel axle bearings

- Take out the clip on the outside of the gearbox

cover.

- Remove the bearing with the adequate tools ad-

equately supporting the hub cover, as shown in the

figure.

Specific tooling

020376Y

Adaptor handle

020364Y

25-mm guide

With the appropriate tools, remove the oil seal as

shown in the figure.

Specific tooling

020376Y

Adaptor handle

020359Y

42x47-mm adaptor

Removing the driven pulley shaft bearing

If it is necessary to remove the driven pulley shaft, from the relevant bearing and oil seal, remove driven

pulley.

- Extract the driven pulley shaft from its bearing.

- Remove the oil guard using a screwdriver, working from inside the bearing and being careful not to

damage the housing, make it come out of the belt transmission side.

- Remove the seeger ring shown in the figure

Engine

SPORTCITY ONE 125

ENG - 78

Содержание SPORTCITY ONE 125

















































































































































































Результаты поиска

Содержание SPORTCITY ONE 125

Отзывы:

Бренды по названию

Популярные бренды

APRILIA SPORTCITY ONE 125, Руководство по обслуживанию станции

Результаты поиска

Содержание SPORTCITY ONE 125

Отзывы:

Бренды по названию

Популярные бренды