APRILIA SPORTCITY ONE 125 Скачать руководство пользователя страница 97

Страница: 97 / 176

Inspecting the springs and half-cones

- Check that the upper spring caps and the cotter

halves show no signs of abnormal wear.

- Check the length clearance of the springs.

Characteristic

Valve spring length

33.9 ÷ 34.4 mm

Refitting the valves

- Lubricate the valve guides with engine oil.

- Place the lower plates of the valve spring on the

head.

- Use the punch to fit the 2 sealing rings one at a

time.

Specific tooling

020306Y

Punch for assembling valve seal

rings

- Fit the valves, the springs and the spring retaining

caps. Using the appropriate tool with adapter 11,

compress the springs and insert the cotters in their

seats.

Specific tooling

020382Y

Tool for removing valve cotters fitted

with part 012

020382Y011

adapter for valve removal tool

Inspecting the cam shaft

- Inspect the cam shaft for signs of abnormal wear

on the cams.

Characteristic

Standard diameter Bearing A

Ø: 32.5 mm -0.025 -0.050 mm

Standard diameter Bearing B

20 -0.020 -0.041 mm

SPORTCITY ONE 125

Engine

ENG - 97

Содержание SPORTCITY ONE 125

















































































































































































Результаты поиска

Содержание SPORTCITY ONE 125

Отзывы:

Бренды по названию

Популярные бренды

APRILIA SPORTCITY ONE 125, Руководство по обслуживанию станции

Результаты поиска

Содержание SPORTCITY ONE 125

Отзывы:

Бренды по названию

Популярные бренды