APRILIA SPORTCITY ONE 125 Скачать руководство пользователя страница 64

Страница: 64 / 176

Automatic transmission

Transmission cover

- To remove the transmission cover it is necessary

to remove the rear plastic cover first by inserting a

screwdriver in the corresponding slotted holes.

Using the clutch bell lock wrench, remove the driv-

en pulley axle locking nut and recover the washer.

- Remove the cap/dipstick from the engine oil filling

hole.

- Remove the 10 screws and the earth cable fas-

tened under one of them.

- Remove the transmission cover. If this operation

is performed directly on the vehicle, it is necessary

to remove the cooling air coupling and the three air

filter housing retainers.

Specific tooling

020423Y

Driven pulley lock wrench

Air duct

- Unscrew the Torx screws fixing the air manifold

bulkhead and remove the bulkhead.

- Remove the 3 screws, then take out the manifold

as well as the filter.

Engine

SPORTCITY ONE 125

ENG - 64

Содержание SPORTCITY ONE 125

















































































































































































Результаты поиска

Содержание SPORTCITY ONE 125

Отзывы:

Бренды по названию

Популярные бренды

APRILIA SPORTCITY ONE 125, Руководство по обслуживанию станции

Результаты поиска

Содержание SPORTCITY ONE 125

Отзывы:

Бренды по названию

Популярные бренды