manualshive.com logo in svg

APRILIA SPORTCITY ONE 125, Руководство по обслуживанию станции

Поделиться
Скачать
APRILIA SPORTCITY ONE 125 Скачать руководство пользователя страница 35

Transmissions

Check that the throttle grip works correctly

CAUTION

DO NOT USE THE SCOOTER IF THE THROTTLE GRIP CABLE IS DAMAGED, TWISTED OR
COILED. THIS MAY INTERFERE WITH THE THROTTLE GRIP NORMAL OPERATION.
THE THROTTLE GRIP MAY GET LOCKED AND THIS MAY RESULT IN LOSS OF VEHICLE CON-
TROL.

Make sure the front fork rotation does not press the throttle grip and engage gears. Furthermore, make

sure that the throttle grip goes back to idle position smoothly and automatically when released.

If this does not occur:

NOTE

USED THE SPECIFIC LUBRICANT AVAILABLE IN THE MARKET TO LUBRICATE THE COMPO-
NENTS.

Check the position and lubrication of the following

components:

•

throttle grip cable sheath;

•

throttle grip regulator «2»;

•

cable terminals;

•

throttle grip.

Check the throttle grip adjustment.

NOTE

APPLY A GOOD QUANTITY OF SCOOTER CABLE
GREASE TO LUBRICATE THE THROTTLE GRIP SYSTEM
COMPONENTS.

Throttle grip adjustment

NOTE

BEFORE CARRYING OUT ANY TYPE OF OPERATIONS, MAKE SURE THE THROTTLE GRIP
WORKS PROPERLY.

The throttle grip cable backslash must be between

2 - 3 mm (0.08 - 0.12 in), measured at the throttle

trim, as shown in the figure.

SPORTCITY ONE 125

Maintenance

MAIN - 35

Содержание SPORTCITY ONE 125

















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды