APRILIA SPORTCITY ONE 125 Скачать руководство пользователя страница 79

Страница: 79 / 176

With the sectional punch, remove the driven pulley

shaft bearing.

Specific tooling

020376Y

Adaptor handle

020375Y

28 x 30 mm adaptor

020363Y

20 mm guide

See also

Inspecting the hub shaft

- Check the three shafts for wear or distortion of

the toothed surfaces, the bearing housings, and

the oil seal housings.

- In case of anomalies, replace the damaged com-

ponents.

Inspecting the hub cover

- Check that the fitting surface is not dented or distorted. - Check the capacity of the bearings and the

brake camshaft. - If faults are found, replace the hub cover.

Refitting the driven pulley shaft bearing

- Heat up the parts using the specific heat gun

Specific tooling

020150Y

Air heater support

020151Y

Air heater

- Reassemble the driven pulley axle bearing positioning it with ball bearing in view from the inside of

the hub cover using the adequate tools

Specific tooling

020376Y

Adaptor handle

SPORTCITY ONE 125

Engine

ENG - 79

Содержание SPORTCITY ONE 125

















































































































































































Результаты поиска

Содержание SPORTCITY ONE 125

Отзывы:

Бренды по названию

Популярные бренды

APRILIA SPORTCITY ONE 125, Руководство по обслуживанию станции

Результаты поиска

Содержание SPORTCITY ONE 125

Отзывы:

Бренды по названию

Популярные бренды