APRILIA SPORTCITY ONE 125 Скачать руководство пользователя страница 93

Страница: 93 / 176

Refitting the cylinder

- Insert the cylinder base gasket with the thickness

determined above.

- Using the fork support and the piston ring retain-

ing band, refit the cylinder as shown in the figure.

NOTE

BEFORE FITTING THE CYLINDER, CAREFULLY BLOW
OUT THE LUBRICATION DUCT AND OIL THE CYLINDER
BARREL.

Specific tooling

020426Y

Piston fitting fork

020427Y

Piston fitting band

Inspecting the cylinder head

- Using a trued bar check that the cylinder head

surface is not worn or distorted.

- Check that the camshaft and rocking lever pin

bearings show no signs of wear.

- Check that the cylinder head cover surface, the

intake manifold and the exhaust manifold are not

worn.

Characteristic

Maximum admitted unevenness: Head check

0.05 mm

STANDARD DIAMETER

Specification

Desc./Quantity

Standard diameter

A Ø 32.5 ÷ 32.525

Standard diameter

B Ø 20 ÷ 20.021

Standard diameter

C Ø 12 ÷ 12.018

SPORTCITY ONE 125

Engine

ENG - 93

Содержание SPORTCITY ONE 125

















































































































































































Результаты поиска

Содержание SPORTCITY ONE 125

Отзывы:

Бренды по названию

Популярные бренды

APRILIA SPORTCITY ONE 125, Руководство по обслуживанию станции

Результаты поиска

Содержание SPORTCITY ONE 125

Отзывы:

Бренды по названию

Популярные бренды