APRILIA SPORTCITY ONE 125 Скачать руководство пользователя

Страница: 86 / 176

- Remove the internal hex screw and the counter-

weight shown in the figure.

- Remove the camshaft command pulley and its

washer.

- Remove the command sprocket wheel and the

timing chain.

- Remove the screws indicated in the figure, the

spacer bar and the tensioner pad.

The chain tensioning pad must be removed from

the transmission side. As regards the lower chain

guide pad, it may only be removed after the head

has been removed.

NOTE

IT IS ADVISABLE TO MARK THE CHAIN IN ORDER TO EN-
SURE THAT THE INITIAL DIRECTION OF ROTATION IS
MAINTAINED.

See also

Electric fan

Removing the cam shaft

- Remove the two screws and the cam shaft re-

tainer shown in the diagram.

- Remove the cam shaft.

Engine

SPORTCITY ONE 125

ENG - 86

Содержание SPORTCITY ONE 125

















































































































































































Результаты поиска

Содержание SPORTCITY ONE 125

Отзывы:

Похожие инструкции для SPORTCITY ONE 125

Бренды по названию

Популярные бренды

APRILIA SPORTCITY ONE 125, Руководство по обслуживанию станции

Результаты поиска

Содержание SPORTCITY ONE 125

Отзывы:

Похожие инструкции для SPORTCITY ONE 125

Бренды по названию

Популярные бренды