APRILIA SPORTCITY ONE 125 Скачать руководство пользователя страница 82

Страница: 82 / 176

Cooling hood

-Remove the housing acting on the 4 retaining

screws.

CAUTION

DURING REMOVAL SLIDE THE HOUSING CONNECTOR
ON THE HOUSING.

- Loosen the clamp and remove the carburettor

from the manifold.

-Remove the complete manifold acting on the 2

retainers as shown in the figure.

- Remove the 2 self threading screws, left and right

and the lateral base retaining screw on the crank-

case base.

- Take off the housings.

- Remove the gasket seal of the housing on the

head.

NOTE

IF THE FLYWHEEL HOUSING IS NOT REMOVED, IT IS AL-
SO NECESSARY TO REMOVE THE TWO KNOB SCREWS.

On the vehicles equipped with the engines mentioned if they are losing a full circle at full gas, we suggest

to intervene on the vacuum socket inserting on the inlet manifold widening the hole from 0.4 mm to 1.5

mm. Remember that such operation must have performed on a disassembled manifold which must be

cleaned afterwards.

Cooling fan

- Remove the cooling fan by acting on the three

fixings indicated in the figure.

Engine

SPORTCITY ONE 125

ENG - 82

Содержание SPORTCITY ONE 125

















































































































































































Результаты поиска

Содержание SPORTCITY ONE 125

Отзывы:

Бренды по названию

Популярные бренды

APRILIA SPORTCITY ONE 125, Руководство по обслуживанию станции

Результаты поиска

Содержание SPORTCITY ONE 125

Отзывы:

Бренды по названию

Популярные бренды