APRILIA SPORTCITY ONE 125 Скачать руководство пользователя

Страница: 32 / 176

CAUTION

DO NOT USE PETROL OR FLAMMABLE SOLVENTS TO CLEAN THE FILTERING ELEMENT TO
AVOID RISK OF FIRE OR EXPLOSION.

•

Wash the filtering element «3» with clean non-inflammable or high-volatility solvents and let

it dry thoroughly.

•

Apply a specific filter oil over all the surface.

Engine oil

Replacement

NOTE

USE RECOMMENDED OIL ONLY. REFER TO THE RECOMMENDED PRODUCTS TABLE.

NOTE

PARK THE VEHICLE ON SAFE AND LEVEL GROUND.

•

Park the vehicle on firm and level ground.

•

Rest the vehicle on its centre stand.

•

Unscrew and take out the measuring

tap-dipstick «1».

•

Place a container to collect the oil un-

der the engine oil filter.

•

Unscrew and remove the engine oil

cartridge filter «2».

CAUTION

USED OIL CONTAINS SUBSTANCES THAT ARE HARM-
FUL TO THE ENVIRONMENT. DISPOSE OF USED OIL AC-
CORDING TO THE REGULATIONS IN FORCE.

•

Unscrew and remove the oil drainage plug «3» and drain off the engine oil.

•

Fit a new oil cartridge filter «2» and lubricate the filter sealing O-rings with oil.

•

Screw and tighten the engine oil drainage plug «3».

•

Pour approx. 1000 cm³ (61 cu.in) of engine oil through the fill opening.

Maintenance

SPORTCITY ONE 125

MAIN - 32

Содержание SPORTCITY ONE 125

















































































































































































Результаты поиска

Содержание SPORTCITY ONE 125

Отзывы:

Похожие инструкции для SPORTCITY ONE 125

Бренды по названию

Популярные бренды

APRILIA SPORTCITY ONE 125, Руководство по обслуживанию станции

Результаты поиска

Содержание SPORTCITY ONE 125

Отзывы:

Похожие инструкции для SPORTCITY ONE 125

Бренды по названию

Популярные бренды