APRILIA SPORTCITY ONE 125 Скачать руководство пользователя

Страница: 131 / 176

- The correct warm up time depends on the ambient temperature.

- If protrusion, resistance or timing values are different from the ones prescribed, replace the starter.

- Assemble the starter to the carburettor being careful to position the O-Ring correctly, insert the plate

with the machined side contacting the starter, tighten the fixing screws.

- Position the starter as shown in the figure.

- Assemble the protection casing.

NOTE

TO CARRY OUT THIS CHECK PAY SPECIAL ATTENTION NOT TO GENERATE SHORT CIRCUITS
USE A CABLE SECTION WITH A TERMINAL SUITABLE TO BE CONNECTED TO THE STARTER.

Characteristic

Starter pin travel

10 mm (at 24°)

Starter resistance

20 Ohm (at 24°)

Check the automatic starter: Keihin maximum time

5 min

SPORTCITY ONE 125

Engine

ENG - 131

Содержание SPORTCITY ONE 125

















































































































































































Результаты поиска

Содержание SPORTCITY ONE 125

Отзывы:

Похожие инструкции для SPORTCITY ONE 125

Бренды по названию

Популярные бренды

APRILIA SPORTCITY ONE 125, Руководство по обслуживанию станции

Результаты поиска

Содержание SPORTCITY ONE 125

Отзывы:

Похожие инструкции для SPORTCITY ONE 125

Бренды по названию

Популярные бренды