manualshive.com logo in svg

APRILIA SPORTCITY ONE 125, Руководство по обслуживанию станции

Поделиться
Скачать
APRILIA SPORTCITY ONE 125 Скачать руководство пользователя страница 54

•

High/low-beam light check

•

Check that bulb operates properly.

•

Check continuity of the Green cable between 15A fuse C and light switch.

•

Check that the light switch operate properly.

•

Check continuity of the Black cable between the light switch and the low-beam bulb.

•

Check continuity of the White cable between the light switch and the high-beam bulb.

Fuses

CAUTION

DO NOT REPAIR FAULTY FUSES.
USE RECOMMENDED FUSES ONLY. USING FUSES OF UNSUITABLE CAPACITY MAY SERI-
OUSLY DAMAGE THE ELECTRICAL SYSTEM OR CAUSE A SHORT CIRCUIT, WHICH MAY
TOTALLY DESTROY YOUR SCOOTER AS WELL AS INJURE YOU.

The vehicle has one fuse located in the battery compartment and two fuses located in the front glove

compartment.

FUSE CHART

Specification

Desc./Quantity

1

Fuse A

Capacity:

 20 A

Protected circuits:

 Recharge circuit, oil pressure sen-

sor, oil pressure warning light .

2

Fuse B

Capacity:

 7.5 A

Protected circuits:

 Start-up circuit, starter motor, stop

light bulb, ECU power supply.

3

Fuse C

Capacity:

 15 A

Protected circuits:

 Rear light bulb, license plate light

bulb, turn indicator bulb, turn indicator warning light, fuel

gauge, instrument panel lighting bulb, horn, low-beam

bulb, high-beam bulb, high-beam warning light.

Electrical system

SPORTCITY ONE 125

ELE SYS - 54

Содержание SPORTCITY ONE 125

















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды