APRILIA SPORTCITY ONE 125 Скачать руководство пользователя страница 53

Страница: 53 / 176

level indicators

CAUTION

THE CONTINUITY TEST SHOULD BE PERFORMED WITH THE RELATIVE CONNECTORS DIS-
CONNECTED.

•

Check continuity of the Green cable which connects the instrument panel to the 15A fuse

•

Check continuity of the Grey-Green cable which connects the instrument panel to the probe

checking fuel level.

•

Measure resistance present between the Grey-Green cable and the Blue cable of the fuel

level probe by moving the arm with the float to different positions.

•

If the values measured are correct but the instrument panel value displayed is incorrect,

check wiring continuity.

Characteristic

Resistance value with empty tank

~ 101

Resistance value with full tank

~ 7.4

Lights list

BULBS AND WARNING LIGHTS

Specification

Desc./Quantity

Low-beam bulb

12 V - 35 W (Halogen) H8

High-beam bulb

12 V - 35 W (Halogen) H8

Tail light bulb

12V - 3W

Front turn indicator bulbs

12 V - 21 W (Halogen) H21W

Rear turn indicator bulbs

12V - 16W

Rear position light /stop light bulb

12V - 5/21W

License plate light bulb

12V - 5W

Instrument panel light bulbs

12V - 1.2W

Oil pressure warning light

12V - 1.2W

Turn indicator warning light

12V - 1.2W

High-beam warning light

12V - 1.2W

CAUTION

THE CONTINUITY TEST SHOULD BE PERFORMED WITH THE RELATIVE CONNECTORS DIS-
CONNECTED.

Check tail lights and panel lightning

•

Check that bulb operates properly.

•

Check continuity between the Green cable of 15A fuse C and the Yellow cables of the tail

lights bulbs.

•

Also check continuity of the Green cable of the instrument panel connector.

SPORTCITY ONE 125

Electrical system

ELE SYS - 53

Содержание SPORTCITY ONE 125

















































































































































































Результаты поиска

Содержание SPORTCITY ONE 125

Отзывы:

Бренды по названию

Популярные бренды

APRILIA SPORTCITY ONE 125, Руководство по обслуживанию станции

Результаты поиска

Содержание SPORTCITY ONE 125

Отзывы:

Бренды по названию

Популярные бренды