manualshive.com logo in svg

APRILIA SPORTCITY ONE 125, Руководство по обслуживанию станции

Поделиться
Скачать
APRILIA SPORTCITY ONE 125 Скачать руководство пользователя страница 57

With the battery charged, a density of 30÷32 Bé, corresponding to a specific weight of 1.26÷1.28, must

be at a minimum temperature of 15° C.

A density reading below 20° Bé indicates that the battery is completely flat and must therefore be

recharged..

If the vehicle is not be used for a certain time (1 month or more), the battery needs to be recharged

periodically.

The battery runs down completely in about three months. Should the battery be fitted on a vehicle, be

careful not to invert the connections, keeping in mind that the (

black

) earth wire marked (-) is connected

to the - 

negative

 terminal whereas the other two 

red

 wires marked (+) are connected to the + 

posi-

tive

 terminal.

Battery recharge

WARNING

BEFORE RECHARGING THE BATTERY, REMOVE THE CAPS OF EACH CELL. KEEP NAKED
FLAMES OR SPARKS AWAY FROM THE BATTERY WHILE CHARGING.

First detach the negative terminal before removing the battery from the vehicle.

Normal bench charging must be performed using the special battery charger, setting the battery charge

selector to the type of battery that requires recharging (that is, at a current equal to 1/10 of the battery

rated capacity). Connections to the power supply source must be implemented by connecting corre-

sponding poles (+ to + and - to -).

The battery should always be kept clean, especially its top side, and the terminals should be coated

with petroleum jelly.

CAUTION

NEVER USE FUSES WITH A CAPACITY HIGHER THAN THE RECOMMENDED CAPACITY. USING
A FUSE OF UNSUITABLE RATING MAY SERIOUSLY DAMAGE THE VEHICLE OR EVEN CAUSE
A FIRE.

CAUTION

ORDINARY DRINKING WATER CONTAINS MINERAL SALTS THAT ARE HARMFUL TO THE BAT-
TERY. CONSEQUENTLY, ONLY USE DISTILLED WATER.

CAUTION

TO ENSURE MAXIMUM PERFORMANCE, THE BATTERY MUST BE CHARGED BEFORE USE.
INADEQUATE CHARGING OF THE BATTERY BEFORE BEING PUT INTO OPERATION SHORT-
ENS BATTERY LIFE.

SPORTCITY ONE 125

Electrical system

ELE SYS - 57

Содержание SPORTCITY ONE 125

















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды