Amazone Cirrus 3002 Скачать руководство пользователя страница 99

Страница: 99 / 209

Commissioning

6.1.2

Requirements for tractor operation with attached machines

WARNING

Risk of breakage during operation of components through unap-
proved combinations of connecting equipment!

Ensure:

•

that the connection device on the tractor has a sufficient permis-

sible noseweight for the noseweight actually in question

•

that the axle loads and weights of the tractor altered by the

drawbar load are within the approved limits. If necessary, weigh

them.

•

that the static actual rear axle load of the tractor does not exceed

the permissible rear axle load

•

that the permissible total weight of the tractor is complied with

•

that the approved load capacities of the tractor tyres are not

exceeded.

6.1.3

Machines without their own brake system

The Cirrus is not permitted in Germany or in several other countries without its own braking system.

WARNING

Risk of contusions, cuts, dragging, catching or knocks from
insufficient tractor brake power.

The tractor must achieve the brake delay specified by the tractor

manufacturer, even with the machine connected.
If the machine does not possess its own brake system:

•

Then the actual tractor weight must be greater than or equal to

(

≥

) the actual weight of the connected machines.

•

The maximum movement speed is 25 km/h.

Cirrus BAH0049-1 09.14

Содержание Cirrus 3002


















































































































































































































Результаты поиска

Содержание Cirrus 3002

Отзывы:

Бренды по названию

Популярные бренды

Amazone Cirrus 3002, Руководство по эксплуатации

Результаты поиска

Содержание Cirrus 3002

Отзывы:

Бренды по названию

Популярные бренды