Amazone Cirrus 3002 Скачать руководство пользователя страница 56

Страница: 56 / 209

Product description

Road transport data (only with an empty seed hopper)

Cirrus

3002

4002

6002

Transport width

[m]

3.0

Overall height in transport position

(folded in from 4 m working width up-

wards)

[mm]

2700

3700

Empty weight (basic weight)

[kg]

3900

5890

7600

Running gear tyre

without polyurethane filling
with polyurethane filling

[kg]

4300

6290

8000

Permissible total weight

[kg]

4200

6200

8000

Running gear tyre

without

polyurethane

filling

with

polyurethane

filling

[kg]

4600

6600

8400

Permissible axle load

[kg]

3500

5500

6900

Running gear tyre

without

polyurethane

filling

with

polyurethane

filling

[kg]

3900

5900

7300

Perm. drawbar load (F

)

when driving on the road

(see rating plate)

[kg]

1100

1500

2000

Maximum payload for transport journeys

[kg]

220

Perm. maximum speed on all non-public

roads, public roads and public ways.

[km/h]

4.9

Necessary tractor equipment

For operation of the machine in compliance with the intended use the

tractor must fulfil the following requirements.

Tractor engine power

Cirrus 3002

from 90 kW (120 bhp) upwards

Cirrus 4002

from 110 kW (150 bhp) upwards

Cirrus 6002

from 147 kW (200 bhp) upwards

Electrical system

Battery voltage:

12 V (volts)

Lighting socket:

7-pin

Cirrus BAH0049-1 09.14

Содержание Cirrus 3002


















































































































































































































Результаты поиска

Содержание Cirrus 3002

Отзывы:

Бренды по названию

Популярные бренды

Amazone Cirrus 3002, Руководство по эксплуатации

Результаты поиска

Содержание Cirrus 3002

Отзывы:

Бренды по названию

Популярные бренды