Amazone Cirrus 3002 Скачать руководство пользователя страница 114

Страница: 114 / 209

Coupling and uncoupling the machine

7.3

Coupling the hydraulic pump (optional)

WARNING

Risk of crushing from tractor and machine unintentionally start-
ing up or rolling away!

Only couple/uncouple the hydraulic pump and tractor universal joint

shaft if the tractor and machine are secured to prevent unintentional

starting and rolling.

7.3.1

Connecting the hydraulic pump

1. Disengage the tractor's universal joint shaft, engage the parking

brake, shut off the engine and remove the ignition key.

  2.  Clean and grease the tractor's universal joint shaft.
  3.  Couple the tractor and machine.
  4.  Secure the tractor against unintentional starting and unintention-

al rolling away.

5. Couple the hydraulic pump (Fig. 115/1) to

the tractor's universal joint shaft.

The hydraulic pump is equipped with a QC

fastener. Make sure that the QC fastener

has engaged correctly.

6. Set the adjuster segment so that the buffer

(Fig. 115/2) rests against it.

Fig. 115

114

Cirrus BAH0049-1 09.14

Содержание Cirrus 3002


















































































































































































































Результаты поиска

Содержание Cirrus 3002

Отзывы:

Бренды по названию

Популярные бренды

Amazone Cirrus 3002, Руководство по эксплуатации

Результаты поиска

Содержание Cirrus 3002

Отзывы:

Бренды по названию

Популярные бренды