Amazone Cirrus 3002 Скачать руководство пользователя страница 100

Страница: 100 / 209

Commissioning

6.2

Securing the tractor / machine against unintentional start-up and roll-
ing

WARNING

Risk of contusions, cutting, catching, drawing in and knocks
when making interventions in the machine through

•

Unintentional lowering of the unsecured machine when it is
raised via the three-point hydraulic system of the tractor

•

Unintentional lowering of raised, unsecured parts of the
machine

•

Unintentional start-up and rolling of the tractor-machine
combination.

•

Secure the tractor and the machine against unintentional start-

up and rolling before any intervention in the machine.

•

It is forbidden to make any intervention in the machine, such as

installation, adjustment, troubleshooting, cleaning, maintenance

and repairs

while the machine is being driven

as long as the tractor engine is running with a connected

hydraulic system.

if the ignition key is inserted in the tractor and the tractor

engine can be started unintentionally with the hydraulic

system connected

if the tractor and machine are not secured with chocks

against unintentional rolling

if moving parts are not blocked against unintentional

movement

When carrying out such work, there is a high risk of contact with

unsecured components.

1. Park the tractor with the machine on firm flat ground only.
2. Lower the raised, unsecured machine / raised, unsecured parts

of the machine.

→

This is how to prevent unintentional falling:

  3.  Shut down the tractor engine.
  4.  Remove the ignition key.
  5.  Apply the tractor parking brake.
  6.  Secure the machine with wheel chocks against unintentionally

rolling away.

100

Cirrus BAH0049-1 09.14

Содержание Cirrus 3002


















































































































































































































Результаты поиска

Содержание Cirrus 3002

Отзывы:

Бренды по названию

Популярные бренды

Amazone Cirrus 3002, Руководство по эксплуатации

Результаты поиска

Содержание Cirrus 3002

Отзывы:

Бренды по названию

Популярные бренды