manualshive.com logo in svg

Amazone Cirrus 3002, Руководство по эксплуатации

Поделиться
Скачать
Amazone Cirrus 3002 Скачать руководство пользователя страница 132

 

 

 

Settings 

 

 

8.8.2 

Adjusting disc array working depth  
with machine setting "Turning on the roller" 

 

Turning the Cirrus 3002 on the roller is not possible. 

 

 

  1.  Set the disc array working depth. 
  2.  Leave the disc array in operational position and stop the tractor.  
  3.  Apply the tractor parking brake, switch off the tractor engine and 

remove the ignition key. 

 

 

 

DANGER 

Apply the tractor parking brake, switch off the tractor engine and 
remove the ignition key. 

 
  4.  Release the wing nuts (Fig. 138/1). 
  5.  Position the sensor (Fig. 138/2) and the 

magnet (Fig. 138/3) one above the other. 

  6.  Tighten the wing nut by hand. 

 

 

Fig. 138 

Pushing the sensor in the direction of the arrow 

increases the working depth of the disc array. 

 

 

 

The disc array 

•

 

is raised before turning at the end of the field, and always as-

sumes the operational position set with the sensor after turning.  

•

 

can be adjusted during work. 

 

132  

Cirrus  BAH0049-1  09.14

 

 

Содержание Cirrus 3002


















































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды