Amazone Cirrus 3002 Скачать руководство пользователя страница 93

Страница: 93 / 209

Commissioning

This section contains information

•

on initial operation of your machine

•

on checking how you may attach the machine to your tractor.

•

Before operating the machine for the first time the operator must

have read and understood the operating manual.

•

Take heed of section "Safety information for users", from Seite

31 onwards on

connecting and disconnecting the machine

transporting the machine

using the machine

•

Only couple and transport the machine to/with a tractor which is

suitable for the task.

•

The tractor and machine must meet the national road traffic

regulations.

•

The operator and the user shall be responsible for compliance

with the statutory road traffic regulations.

WARNING

Risk of contusions, cutting, catching, drawing in and knocks in
the area of hydraulically or electrically actuated components.

Do not block the operator controls on the tractor which are used for

hydraulic and electrical movements of components, e.g. folding,

swivelling and pushing movements. The movement must stop auto-

matically when you release the appropriate control. This does not

apply to equipment movements that:

•

are continuous or

•

are automatically locked or

•

due to their function require a float position or pressure position.

Cirrus BAH0049-1 09.14

Содержание Cirrus 3002


















































































































































































































Результаты поиска

Содержание Cirrus 3002

Отзывы:

Бренды по названию

Популярные бренды

Amazone Cirrus 3002, Руководство по эксплуатации

Результаты поиска

Содержание Cirrus 3002

Отзывы:

Бренды по названию

Популярные бренды