Amazone Cirrus 3002 Скачать руководство пользователя страница 64

Страница: 64 / 209

Structure and function

5.4

Hydraulic operating brake system

To control the hydraulic operating brake system, the tractor requires

hydraulic braking equipment.

5.4.1

Coupling the hydraulic operating brake system

Only couple clean hydraulic couplings.

1. Remove the protective cap (Fig. 56/1).
2. If necessary, clean the hydraulic connectors

(Fig. 55) and hydraulic connector socket.

3. Connect the hydraulic connector socket on

the machine face with the hydraulic con-

nector on the tractor face.

Fig. 55

5.4.2

Uncoupling the hydraulic operating brake system

1. Unlock the hydraulic connectors from the

hydraulic sockets.

2. Secure the hydraulic connectors and hy-

draulic connector socket with protective

caps (Fig. 56/1) against soiling.

3. Place the hydraulic hose line in the hose

cabinet.

Fig. 56

Cirrus BAH0049-1 09.14

Содержание Cirrus 3002


















































































































































































































Результаты поиска

Содержание Cirrus 3002

Отзывы:

Бренды по названию

Популярные бренды

Amazone Cirrus 3002, Руководство по эксплуатации

Результаты поиска

Содержание Cirrus 3002

Отзывы:

Бренды по названию

Популярные бренды