Amazone Cirrus 3002 Скачать руководство пользователя страница 113

Страница: 113 / 209

Coupling and uncoupling the machine

13. Set the machine down on the sustainer.

Fig. 113

WARNING

Set the machine down on a hori-
zontal, firm base only!

Ensure that the sustainer does not
sink into the ground. If the sus-
tainer does sink into the ground, it
will be impossible to recouple the
machine!

14. Open the securing device (Fig. 114) of the

tractor's lower link (see tractor operating

manual).

15. Uncouple the tractor's lower link.
16. Pull the tractor forwards.

Fig. 114

DANGER

While pulling the tractor forwards
no personnel are allowed to be
between the tractor and the ma-
chine!

CAUTION

Danger of getting crushed in the area of the moving draw rail.

Cirrus BAH0049-1 09.14

113

Содержание Cirrus 3002


















































































































































































































Результаты поиска

Содержание Cirrus 3002

Отзывы:

Бренды по названию

Популярные бренды

Amazone Cirrus 3002, Руководство по эксплуатации

Результаты поиска

Содержание Cirrus 3002

Отзывы:

Бренды по названию

Популярные бренды