Amazone Cirrus 3002 Скачать руководство пользователя страница 163

Страница: 163 / 209

Use of the machine

counter displays "0" on the AMATRON 3 display.

•

Lowering the discs of the tramline marker if the tramline counter

displays "0" on the AMATRON 3 display.

5. Lower/raise the tractor's lower link until the machine is approxi-

mately horizontal. As an orientation aid, there is a chain beside

the draw rail.

6. Check and, if required, correct the tramline rhythm on the AMA-

TRON 3 display (see the AMATRON 3 operating manual).

7. Check and, if required, correct the tramline counter on the AMA-

TRON 3 display (see the AMATRON 3 operating manual).

8. Actuate control unit

green

(only with the machine setting "Turning on the axle").

→

Actuate control unit

green

until the required disc array working

depth has been reached.

9. Start.

10.8

Checks

After 100 m check and correct as necessary the:

•

Working intensity of the disc array

•

Planting depth of the seed .

•

Working intensity (depending on the equipment)

of the exact harrow,

of the drag tines

of the seed pressure rollers.

Check on a change from light soil to heavy soil and vice versa

•

Planting depth of the seed.

10.8.1

Checking the seed planting depth

1. Sow approximately 100 m at working speed.
2. Uncover the seed at several points and check the placement

depth.

Cirrus BAH0049-1 09.14

163

Содержание Cirrus 3002


















































































































































































































Результаты поиска

Содержание Cirrus 3002

Отзывы:

Бренды по названию

Популярные бренды

Amazone Cirrus 3002, Руководство по эксплуатации

Результаты поиска

Содержание Cirrus 3002

Отзывы:

Бренды по названию

Популярные бренды