Amazone Cirrus 3002 Скачать руководство пользователя страница 94

Страница: 94 / 209

Commissioning

6.1

Checking the suitability of the tractor

WARNING

Danger of breaking during operation, insufficient stability and
insufficient tractor steering and braking power on improper use
of the tractor!

•

Check the suitability of your tractor before you attach or hitch the

machine to the tractor.

You may only connect the machine to tractors suitable for the

purpose.

•

Carry out a brake test to check whether the tractor achieves the

required braking delay with the machine connected.

Requirements for the suitability of a tractor are, in particular:

•

The approved total weight

•

The approved axle loads

•

The approved drawbar load at the tractor coupling point

•

The load capacity of the installed tyres

•

The approved trailer load must be sufficient

You can find this data on the type plate or in the vehicle docu-

mentation and in the tractor operating manual.

The front axle of the tractor must always be subjected to at least 20%

of the empty weight of the tractor.
The tractor must achieve the brake delay specified by the tractor

manufacturer, even with the machine connected.

Cirrus BAH0049-1 09.14

Содержание Cirrus 3002


















































































































































































































Результаты поиска

Содержание Cirrus 3002

Отзывы:

Бренды по названию

Популярные бренды

Amazone Cirrus 3002, Руководство по эксплуатации

Результаты поиска

Содержание Cirrus 3002

Отзывы:

Бренды по названию

Популярные бренды