Amazone Cirrus 3002 Скачать руководство пользователя страница 53

Страница: 53 / 209

Product description

4.6

Danger area and danger points

The danger area is the area around the machine in which people can

be caught:

•

By work movements made by the machine and its tools

•

By materials or foreign bodies thrown out of the machine

•

By tools rising or falling unintentionally

•

By unintentional rolling of the tractor and the machine

Within the machine danger area, there are danger points with perma-

nent or unexpected risks. Warning pictograms indicate these danger

points and warn against residual dangers, which cannot be eliminated

for construction reasons. Here, the special safety regulations of the

appropriate section shall be valid.
No-one may stand in the machine danger area:

•

as long as the tractor engine is running with a connected hydrau-

lic system.

•

as long as the tractor and machine are not protected against

unintentional start-up and running.

The operating person may only move the machine or switch or drive

the tools from the transport position to the working position or vice-

versa when there is no-one in the machine danger area.
Danger points exist:

•

in the area of the swivelling machine extension arm

•

in the area of the swivelling track marker

•

in the area of the swivelling tapered ring tyres.

Cirrus BAH0049-1 09.14

Содержание Cirrus 3002


















































































































































































































Результаты поиска

Содержание Cirrus 3002

Отзывы:

Бренды по названию

Популярные бренды

Amazone Cirrus 3002, Руководство по эксплуатации

Результаты поиска

Содержание Cirrus 3002

Отзывы:

Бренды по названию

Популярные бренды