Amazone Cirrus 3002 Скачать руководство пользователя страница 37

Страница: 37 / 209

General Safety Instructions

2.16.4

Universal joint shaft operation

•

You must install or remove the PTO shaft only after you have

done all of the following:

Switched off the universal joint shaft

Switched off the tractor engine

Applied the parking brake

The ignition key has been removed

•

Before switching on the universal joint shaft, check that the se-

lected universal joint shaft speed of the tractor matches the per-

mitted drive speed of the machine.

•

Instruct everyone to leave the danger area of the machine before

switching on the universal joint shaft.

•

Never switch on the universal joint shaft when the tractor engine

is not running.

•

WARNING After the universal joint shaft is switched off, there is

a risk of injury from the continued rotation of freewheeling ma-

chine parts.

Stay clear of the machine during this time. You must only start

work on the machine once all machine parts are at a complete

standstill.

2.16.5

Attached machines

•

Comply with the approved combination options for the attach-

ment equipment on the tractor and the machine drawbar.

Only couple approved combinations of vehicles (tractor and

attached machine).

•

In the case of single axle machines, observe the maximum per-

mitted drawbar load of the tractor on the attachment equipment.

•

Ensure that the tractor has sufficient steering and braking power.

Machines connected to a tractor can influence your driving be-

haviour, as well as the steering and braking power of the tractor,

in particular in the case of single axle machines with the drawbar

load on the tractor.

•

Only a specialist workshop may adjust the height of the drawbar

on yoke bars with a drawbar load.

Cirrus BAH0049-1 09.14

Содержание Cirrus 3002


















































































































































































































Результаты поиска

Содержание Cirrus 3002

Отзывы:

Бренды по названию

Популярные бренды

Amazone Cirrus 3002, Руководство по эксплуатации

Результаты поиска

Содержание Cirrus 3002

Отзывы:

Бренды по названию

Популярные бренды