Amazone Cirrus 3002 Скачать руководство пользователя страница 108

Страница: 108 / 209

Coupling and uncoupling the machine

7.1.1

Hydraulic connections

•

All hydraulic hose lines are equipped with grips.

Coloured markings with a code number or code letter have been

applied to the gripping sections in order to assign the respective

hydraulic function to the pressure line of a tractor control unit!

Films are stuck on the implement for the markings that illustrate

the respective hydraulic function.

•

The tractor control unit must be used in different types of activa-

tion, depending on the hydraulic function.

Latched, for a permanent oil circulation

Tentative, activate until the action is executed

Float position, free oil flow in the control unit

Marking

Function

Tractor control unit

yellow

Pre-

selection

via

switch tap

Running gear /

track marker /

pre-emergence

marker

Put in working position

Double-

acting

Put headlands position

yellow

Turning on the

roller

Lowering the coulter frame/ disc

array

Double-

acting

Lifting the coulter frame / disc

array

green

Pre-

selection

via

switch tap

machine exten-

sion arms

Fold out

Double-

acting

Fold in

green

exact harrow

coulter pres-

sure

Increase

Double-

acting

Decrease

green

Disc array

depth adjust-

ment

Increase

Double-

acting

Decrease

red

Hydraulic fan motor

Single-

acting

red

Pressure-free return flow

108

Cirrus BAH0049-1 09.14

Содержание Cirrus 3002


















































































































































































































Результаты поиска

Содержание Cirrus 3002

Отзывы:

Бренды по названию

Популярные бренды

Amazone Cirrus 3002, Руководство по эксплуатации

Результаты поиска

Содержание Cirrus 3002

Отзывы:

Бренды по названию

Популярные бренды