Amazone Cirrus 3002 Скачать руководство пользователя страница 103

Страница: 103 / 209

Coupling and uncoupling the machine

When coupling and uncoupling the machine take heed of the section

"Safety information for users", Seite 31.

WARNING

Risk of contusions from unintentional starting and rolling of the
tractor and machine when coupling or uncoupling the machine!

Secure the tractor and machine against unintentional start-up and

rolling away before entering the danger area between the tractor and

machine to couple or uncouple the machine.

WARNING

Risk of contusions between the rear of the tractor and the ma-
chine when coupling and uncoupling the machine!

Only actuate the operator controls for the tractor's three-point hydrau-

lic system

•

from the workplace provided

•

if you are outside of the danger area between the tractor and the

machine.

7.1

Coupling the machine

WARNING

Danger of breaking during operation, insufficient stability and
insufficient tractor steering and braking power on improper use
of the tractor!

You may only connect the machine to tractors suitable for the pur-

pose.

WARNING

Risk of contusions when coupling the machine and standing
between the tractor and the machine!

Instruct people to leave the danger area between the tractor and the

machine before you approach the machine.
Any helpers may only act as guides standing next to the tractor and

the machine, and may only move between the vehicles when both are

at a standstill.

Cirrus BAH0049-1 09.14

103

Содержание Cirrus 3002


















































































































































































































Результаты поиска

Содержание Cirrus 3002

Отзывы:

Бренды по названию

Популярные бренды

Amazone Cirrus 3002, Руководство по эксплуатации

Результаты поиска

Содержание Cirrus 3002

Отзывы:

Бренды по названию

Популярные бренды