Amazone Cirrus 3002 Скачать руководство пользователя страница 191

Страница: 191 / 209

Cleaning, maintenance and repairs

12.5.6

Service brake system:
dual-circuit pneumatic braking system - hydraulic braking system

The Cirrus is equipped with a dual-circuit pneumatic braking system

with a hydraulically actuated brake cylinder.
The dual-circuit pneumatic braking system does not actuate as nor-

mally a rod or brake cable connected to the brake shoe.
The dual-circuit pneumatic braking system acts on a hydraulic cylin-

der, which actuates the hydraulic brake cylinder of the brake shoes in

the brake drum.

WARNING

The service brake system does not have a parking brake!

Always use wheel chocks before uncoupling the machine from
the tractor.

If the visual inspection, function or action testing of the service brake

system shows any signs of deficiencies, have a thorough inspection

of all components performed immediately at a specialist workshop.

CAUTION

Observe the legal regulations for all service work.

Only genuine spare parts may be used.

The brake valve settings laid down by the manufacturer must not
be altered.

DANGER

•

Only specialist workshops or recognised brake services
may perform adjustment and repair work on the brake sys-
tem.

•

Have the brake system checked regularly.

•

Be particularly careful with welding, burning and drilling
work in the vicinity of brake lines!

•

No welding or soldering may be performed on valve fittings
or pipes. Any damaged parts must be replaced.

•

Always perform a braking test after any adjusting or repair
work on the braking system.

•

For servicing and maintenance work on the braking system
observe the section "Safety information for users", Seite 31.

Cirrus BAH0049-1 09.14

191

Содержание Cirrus 3002


















































































































































































































Результаты поиска

Содержание Cirrus 3002

Отзывы:

Бренды по названию

Популярные бренды

Amazone Cirrus 3002, Руководство по эксплуатации

Результаты поиска

Содержание Cirrus 3002

Отзывы:

Бренды по названию

Популярные бренды